KNOWING ESSENTIAL PLUMBING SKILLS IS CRUCIAL FOR INSTALLING A BATHTUB

Knowing Essential Plumbing Skills is Crucial For Installing a Bathtub

Knowing Essential Plumbing Skills is Crucial For Installing a Bathtub

Blog Article

Book

How do you actually feel in relation to How to Install a Bathtub?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably tough task. If the old tub is conveniently easily accessible, the task can relocate quickly; if you have to open a wall to eliminate the old bathtub as well as position the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub and also embeded in the new one. Make sure you have qualified on your own for the task and are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed project, it is far better to think about utilizing one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This short article will help you install a brand-new bathtub in your bathroom if you have actually currently bought a brand-new bathtub and also do not require to change the plan of your previous supply of water pipes.
Your devices as well as material checklist must consist of the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Getting ready for the Setup


    To start with, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to avoid stress on the bathtub.
    Fit the adaptable tap ports to the bottom of the two taps using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.

    Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The process of removing the existing taps can be quite troublesome due to the restricted access that is often the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
    Prior to going on to fit the new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Tub


    Making use of both wooden boards under its feet, position the tub in the required position. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
    The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the tub till the level checks out degree.
    To mount faucets, fit the bottom of the outermost versatile faucet port to the suitable supply pipe by making a compression join; then do the same for the other faucet.
    Activate the supply of water and examine all joints and new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise examine the overflow outlet and the regular outlet for leakages.
    Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the bath tub must wait till the tub has actually been made use of a minimum of when as this will settle it into its final position.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in location in between the tap and the sink. Safeguard the faucet in position with the manufacturer supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former kind needs to be connected to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the location where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about problems with wetness and possible leakages to the ceiling below.
    You can select from a selection of coloured sealers to assimilate your components and installations. They are sold in tubes and also cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can fracture rather very early if you do not take into account this motion before securing.
    Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles using waterproof or waterproof glue as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    We are very eager about Installing A Bathtub and I am hoping you liked the entire page. Enjoyed our posting? Please share it. Let somebody else check it out. Thanks so much for going through it.


    Schedule Your Job Now

    Report this page